Tag Archives: measuring overhangs

What is the Correct Overhang Distance?

Welcome to Ask the Pole Barn Guru – where you can ask questions about building topics, with answers posted on Mondays.  With many questions to answer, please be patient to watch for yours to come up on a future Monday segment.  If you want a quick answer, please be sure to answer with a “reply-able” email address.

Email all questions to: PoleBarnGuru@HansenPoleBuildings.com

DEAR POLE BARN GURU: I am still building my pole barn. I have recently finished the roof metal and ridge cap. While looking at the construction manual for installing the soffit and roof trims I noticed a conflict of information.

On page 119 figure 16-4 shows an overhang of 2 1/4” to 2 1/2”

On page 365 figure 55-20 shows an overhang of 1 1/2” to 1 3/4”

Which is the correct overhang distance? AARON IN VIRGINIA

DEAR AARON: Actually BOTH of them are correct, and here is why. On Page 119, the overhang is from the outside edge of the eave girt BEFORE the steel siding is applied (no sidewall eave overhang situation). The steel siding is 3/4″ thick, which leaves 1-1/2″ to 1-3/4″ of overhang past the siding after it is installed. On Page 365, the overhang is beyond a fascia board (buildings with eave overhangs). The net resultant of each is the same and perfect for gutters, if they are installed.

Mike the Pole Barn Guru

DEAR POLE BARN GURU: Hi, We purchased a Pole Barn kit from you several years ago.  When installing the roof my husband (the non-builder man) would miss the wood that he was supposed to screw the roofing screw into.  With that said we have screw holes in the roof which are really leaking.   We really need to try to plug the screw holes somehow!

What would you suggest to use to plug the holes in my metal blue roof? SHIRL

DEAR SHIRL: There is a good chance this is easier solved than imagined.

Step #1 Clearly identify where the leaks are – puddles on the floor are a good clue, as are “shiners” (screws which have obviously missed a purlin).

In most cases the “misses” will be several screws along a particular roof purlin where the purlin bowed up towards the ridge or down towards the eave past the pre-drilled holes in the roof steel. If this is the case, one person needs to carefully get up on the roof and utilizing adequate safety precautions, remove the screws from that particular purlin. From the inside, another person needs to push the purlin uphill or downhill far enough so as the screws will now hit it.

In the case of just a random miss – remove the screw, have one person hold a block of wood securely beneath the hole and run the screw back through the hole.

Screws which were not driven in straight or with the EPDM washers adequately compressed can also be a source of leaks, which can be remedied by removing reinstalling the offending screws.

In no case should caulking or other sealants be applied to a screw hole, as they will not afford a permanent fix.

Mike the Pole Barn Guru

DEAR POLE BARN GURU: Howdy,

Noticed a magazine report on treated poles and questioned our treater on their .23 treatment vs. the .60 you mentioned and they said it is equivalent, the only difference is the chemical used. Curious on your take, and if you feel these are ok to go in the ground?

JOEL from MIDLAKES METAL SALES

DEAL JOEL: As best I can tell from the data presented, any of the treatment combinations which meet the UC-4B treating requirements should be totally adequate for structural in ground use (burying them in the ground).

For more reading on MCA pressure preservative treating: https://www.hansenpolebuildings.com/2013/08/mca-micronized-copper-technology/

Here is an article I wrote for Rural Builder magazine on pressure treating, as well: https://www.hansenpolebuildings.com/2014/05/building-code-3/

Mike the Pole Barn Guru